Vista Ademco -10SE Betriebsanweisung PDF herunterladen (Seite 2)

BYPASSING ZONES

Use the 6 BYPASS key when you want to arm your system with one or more zones

intentionally unprotected. The system must be disarmed first.

Mode Press these keys… What happens

BYPASS

ZONES

4-digit code + 6 +

2-digit zone numbers

to be bypassed

• When finished, the keypad will momentarily display

a "Bypass" message for each bypassed zone

number. Wait for all bypassed zones to be displayed.

• Arm the system as usual. When armed, the arming

message is displayed with “ZONE BYPASSED.”

• Bypassed zones are unprotected and will not cause

an alarm if violated.

• The system will not allow fire zones to be bypassed.

• Zones are automatically unbypassed when the

system is disarmed.

• To display bypassed zones prior to arming, enter

your security code and press the BYPASS key.

PANIC KEYS

Your system may have been programmed to use special keys or key pairs to manually

activate emergency (panic) functions as follows:

This Function Key(s)* Sends This Signal** With This Sounding…

Silent Alarm silent alarm

no audible alarm; displays, “Press [∗]

to show faults,” indicating that a silent

alarm has been initiated.

Audible Alarm audible alarm a loud, steady alarm at keypad(s) and

at any external sounders that may be

connected.

Personal Alarm auxiliary alarm steady alarm sound at keypad(s), but

not at external bells or sirens.

Fire Alarm fire alarm temporal (pulsing) sound at external

bells and sirens.

* Enter the appropriate keys programmed by your installer for each function (see installer).

** All panic functions send signals to the Central Monitoring Station, if connected.

To activate a Panic Function:

Press and hold down for at least 2 seconds

the programmed lettered key or key pair

for the desired emergency function (or

press both keys of the assigned key pair at

the same time).

Keys Pairs Displayed as Zone

[A]

(∗

∗∗

∗/1)

[B]

(∗

∗∗

∗/#)

[C]

(3/#)

NOTE: The [D] key may be programmed

for other purposes; see your installer.

CHECKING OPEN ZONES

Checking Zones: Before arming your system, all protected doors, windows and other

detection zones must be closed or bypassed; otherwise the keypad displays "Not Ready."

GOTO: If the user is authorized, a keypad in one partition can be used to perform system

functions in the other partition by using the GOTO command. Must use an Alpha keypad.

Mode Press these keys… What happens

CHECK

ZONES

∗

∗∗

∗

• Displays all faulted zones.

GOTO

4-digit code +

∗

∗∗

∗

partition number

(1,2,3 = go to partition;

0 = return to home part.)

• The keypad beeps to confirm the partition change.

• Keypads automatically return to their original

partition after 30 seconds with no keypad activity.

ARMING THE SYSTEM, CHIME MODE, and CONTROLLING DEVICES

Before arming, close all perimeter doors and windows and make sure the Ready to Arm

message is shown.

After arming, leave the premises through an entry/exit door during the exit delay period and

be sure the door is reclosed to avoid causing an alarm.

Mode Press these keys… When to use an arming mode and what happens

STAY

4-digit code + 3

three beeps confirm

• Used when you want to arm the system with

persons staying inside (or if you have pets that are

moving throughout the premises).

• Arms perimeter zones; interior zones left disarmed.

• An alarm sounds if any protected window or non-

entry/exit door is opened.

NIGHT-

STAY

4-digit code + 3 3

three beeps confirm

• Use NIGHT-STAY mode to provide increased

security while staying inside.

• Arms same as STAY mode, but also arms

preselected interior sensors (set by your installer).

INSTANT

4-digit code + 7

three beeps confirm

• Used when staying inside and do not expect anyone

to use an entry/exit door.

• Same as STAY mode, except entry delay is off.

• An alarm sounds same as STAY mode, and sounds

upon opening entry/exit doors.

AWAY

4-digit code + 2

two beeps confirm

• Used when nobody is staying inside (including pets).

• Arms the entire system (interior and perimeter).

• An alarm sounds if a protected window or any door

is opened, or if any movement is detected inside.

MAXIMUM

4-digit code + 4

two beeps confirm

• Used when leaving the premises for extended

periods (e.g., vacation).

• Same as Away mode, except entry delay is off.

• An alarm sounds same as Away mode, and sounds

upon opening entry/exit doors.

QUICK

ARMING

# + arming key

• If programmed, you can press the [#] key in place

of your security code when arming the system

CHIME

MODE

4-digit code + 9

(enter again to turn

Chime mode off)

• Alerts you to the opening of a perimeter door or

window while the system is disarmed.

• Three tones sound at the keypad whenever a

perimeter door or window is opened (interior zones

do not produce a tone when they are faulted).

• Pressing the READY key displays the open zones.

Turning

Devices

On and

Off

Turn ON a Device:

4-digit code + # +

7 + device number

Turn OFF a Device:

4-digit code + # +

8 + device number

• You may be able to override automatically

controlled devices using the Device commands.

• Some devices can be manually turned on or off

using the Device commands.

• Devices are assigned 2-digit device numbers.

• See your Installer for details on controlling devices.

DISARMING THE SYSTEM and SILENCING ALARMS

The 1 OFF key is used to disarm the system, silence alarm and trouble sounds, and clear

memory of alarm displays.

Mode Press these keys… What happens

DISARM

and

SILENCE

ALARMS

4-digit code + 1

• System is disarmed and alarm sounding is silenced.

• To clear the memory of alarm display (if present),

enter your 4-digit code + 1 again.

• To Silence a Fire Alarm or Carbon Monoxide Alarm

Simply press the 1 key (no code needed)

V20P-Quik-Guide

ARMING

KEYS

BYPASSING

ZONES

CHIME

MODE

QUICK

ARMING

TESTING

THE SYSTEM

ADDING SECURITY

CODES

CHECKING

ZONES

ARMED

READY

ARMING KEYS

(NO DELAY)

DISARM

KEY

OFF

MAX

INSTANT

READY

AWAY

TEST

CODE

STAY

BYPASS

CHIME

• When entering codes and commands, sequential key depressions must be made within 4-5

seconds of one another. If 4-5 seconds elapse without a key depression, the entry will be

aborted and must be repeated from its beginning.

• If you make a mistake while entering a security code, stop, press the

∗

∗∗

∗

key, and then

start over. If you stop in the middle while entering a code, and then immediately start the

entry over, an erroneous code might be entered.

SECURITY CODES

Your installer assigned a master code that is used to perform all system functions.

In addition, other security codes can be assigned for use by other users.

• Only the System Master and Partition Master can assign security codes to users.

• Users are identified by 2-digit user numbers.

• Only the System Master can change user partitions.

• In addition to a security code, each user is assigned an authority level and various system

attributes. See the full User Guide for definitions of each Authority Level.

• Security codes can be used interchangeably within a partition when performing system

functions (a system armed with one security code can be disarmed by a different security

code), with the exception of the Guest and Arm Only codes.

• Security code programming involves these steps:

1. Choose a user number from the set of users assigned to the partition in which the user

will be operating, and assign a 4-digit security code.

2. Assign an authority level to that user.

3. Assign other attributes as necessary.

Assigning Security Codes and User Attributes

The following lists the various command strings for adding security codes and attributes.

NOTE: Partition Master codes (VISTA-20P Series only) apply only to those user numbers

previously assigned (by the system master/installer) to the partition master’s partition.

Function Commands

Change System

Master Code

System Master code + 8 + [02] + new code + new code again

Add Security Code

Master code + 8 + user no. + new user’s security code

The Keypad beeps once to confirm that new user was added.

Delete Security

Code

Master code + 8 + [user no.] + # 0

The security code and all attributes* set for this user number,

including any associated RF keys, are erased from the system.

(*except assigned partition)

Authority Level

Master code + 8 + [user no.] + # 1 + auth. level

Authority Levels: 0 = standard user

1 = arm only

2 = guest

3 = duress

4 = partition master (VISTA-20P Series only)

Access Group

Master Code + 8 + [user no.] + 8 2 + group (1-8)

You can assign users to a group, then set an access schedule that

defines the times this group of users can operate the system. The

system ignores these users outside the scheduled times.

User’s Partition

System Master Code + 8 + [user no.] + # 3 + 0 + part. + #

This assigns the partitions the user can access. If more than one,

enter partition numbers sequentially, then press [#] to end.

E.g., master code + [8] + [user no.] + [#] [3] + [0] + [1] [2] + [#]

gives the user access to partitions 1 and 2 and common partition.

Partition Entries: 1 = partition 1 and common

2 = partition 2 and common

3 = common partition only

RF User Number

Master/Part. Prog. Code + 8 + [user no.] + # 4 + zone no.

Use this command to assign a wireless button device (keyfob) to

this user (keyfob must be enrolled in system first; see installer).

Zone number: enter the zone number assigned to a button on the

keyfob that will be used for arming/disarming by this user.

Pager On/Off

Master/Part. Prog. Code + 8 + [user no.] + # 5 + 0 or 1

You can program a user so that a message is sent to a pager

whenever this code is used to arm or disarm the system.

Paging On/Off: 1 = allow paging

0 = no paging for this user

1 2

ÊK5309-1QGDŠ 1
V20P-Quik-Guide 2

Kommentare zu diesen Handbüchern

Keine Kommentare

Vista Ademco -10SE Betriebsanweisung Seite 2

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Sicherheitszugriffskontrollsysteme Vista Ademco -10SE