Vista Ademco -10SE Anleitung zur Fehlerbehebung PDF herunterladen (Seite 41)

Instal/jointfilesconvert/304319/bg 5S00 Series Tranmmtt

—

“em

To be sure reception of the transmitter’s signal at the proposed mounting

locationis adequate,perform a Go/No Go test.

GdNo Go

Test Mode

The Go/No Go testswill veri& adequateRF signal strength fkomthe proposed

transmitter location, and allow you to reorient or relocate transmitters if

necessary,beforemounting the transmitters permanently.

This mode is eimiIar to the transmitter test mode, exceptthat the wireless

receivergain is reduced.This will enableyou to make sure that the RF signal

horn eachhansmitter is receivedwith su.fiicientsignal amplitude when the

systemis h the normal operatingmode.

1. With at least one 2-line Alpha keypad (5137AD or 6139) connectedto the

system, power up the system temporarily. If you had previously

connectedthe AC hnsformer to the contiol panel, you need only plug in

the transformer (to 120VAC outlet)to powerup the system.

2. Enter installer code (4112)+ # + 4. For multi-partition systems,make

sure all partitions are disarmedbeforeentering this mode.

3. Once you have placed transmitters in their desired locations and the

approximate length of wire to be run to sensors is connected to the

transmitter’s screwtermbls (ifused), fault each transmitter. Do not

conduct this test with your hund wrapped around the transmitter as this

will cause in.u.ccurateresults.

Not@ On button @pe transmitters whosebuttons have been set to Arm

Away, Arm Stay, or Disarm, pressinga button wi.Utake the system out of

the Go/No Go Test modeend causethat action-

a. The keypad will beep three times to indicate signal reception and

displaythe appropriatezonenumber.

b. If the keypad does not beep, reorient or move the transmitter to

another location.Usuelly a few inchesin either direction is all that is

eed.

4. If each transmitter produces the proper keypad response when it is

faulted, you can then permanently mount each of the transmitters

amordingto the instructionsprovidedwith them.

5. Exit the Go/No Go test modeby en- Installer code (4112)+ o~.

6 Unplug the AC transformer.

fh@ing DIPswEtches onthe5827T

rammdtter(s)

A 5827

lmmemitter must be set to the selectedHouse ID, using its DIP

switches.If a 5827 is also being used in partition 2, you must set its DIP

switchto an ID that is one number higher than the one in partition 1 (e.g.,if

House ID selectedis 11, setthe 5827 in partition 1 to “11”, and the 5827 in

partition 2 to “12”.

SWTCHUPFORW

12345

HOUSE ID SWITCH OOWN FOR VFF

SHOWN SEr FORHOUSEiO#30

5827 Wireless Keypad DIP S

1 (XF [ @F

F cm

OFFIGF OFFIOn

3 GF CPFOFFon

cm’

OFF

on CtF

UT m= on

OFFiOfI

6 &F O=Fon OFF h

7 &FcPF on on&

8 W& OFFW=

9 OFF OIOFFOFFCII

10 CPFOIIOFFOFFQI

CPFO!OfF OnOn

12 CfF~On

OFF OFF

13 CPFO1On OFF OfI

14 GFcnon onOfF

witch Table

,-, .-, ,,. ...”

112131415

17 loll -FltXFl O+F

18 [on

CFFIOfF IOn

19 on CFFl OFPfOn

20 Q! OPF

OFF C#

ul C+F

m OFF On

22 *

OFF

m on

OFF

a -

CPF

on on on

24 on al

OFF @F IOF!=

I 2E Ion

ion IOFFIOFFIGI

1-1–111

23 on

2s on on

OFF on

30 on al

on cm w

31 on

Cm on al

-41-

1 2 ... 36 37 38 39 40 41 42 43 44 45 46 ... 119 120

Kommentare zu diesen Handbüchern

Keine Kommentare

Vista Ademco -10SE Anleitung zur Fehlerbehebung Seite 41

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Sicherheitszugriffskontrollsysteme Vista Ademco -10SE